概述
ISE 配置flash
http://www.xilinx.com/support/documentation/sw_manuals/xilinx14_7/pim_r_supported_spi_bpi_proms.htm
iMPACT
SPI, BPI, and NAND PROM Support
iMPACT supports select SPI and BPI Flash memories.The Flash devices supported by iMPACT are listed in the tablesbelow.
iMPACT SPI Flash Programming Support
7 Series FPGA Family Support
| FlashVendor | Flash Family | Supported Flash Density | SPI Indirect Programming Support |
| Micron (Numonyx) | N25Q 3.3V (1) | 32Mb – 256Mb | Kintex™-7, Artix™-7 |
| N25Q 1.8V (1) | 32Mb – 256Mb | Kintex-7,Virtex-7, Artix-7 | |
| Winbond | W25Q (Rev BV) | 32Mb – 128Mb | Kintex-7 |
| W25Q (Rev BW) | 8Mb | Artix-7 | |
| W25Q (Rev FV) | 64Mb – 128Mb | Kintex-7 | |
| W25Q (Rev DW) | 32Mb – 64Mb | Kintex-7, Virtex®-7. Artix-7 | |
| Spansion | S25FLxxP (2) | 32Mb – 256Mb | Kintex-7 |
| S25FLxxS (3) | 128Mb, 512Mb | Kintex-7 | |
| S25FLxxS (3) | 256Mb, 512Mb | Virtex-7 | |
| S25FLxxS (3) | 128Mb, 256Mb | Artix-7 |
- For Numonyx N25Q: Top, Bottom, and Uniform block sectors aresupported.
- S25FL129P and S25FL256S are supported. 64Kb sector size only.S25FL128P is not supported.
- 64kB sector size only.
Virtex and Spartan FPGA Family Support
| FlashVendor | Flash Family | Supported Flash Density | SPI Indirect Programming Support |
| Micron(Numonyx) | M25P | 512kB – 128Mb | Spartan®-3E, Spartan-3A, Spartan-3A DSP, Spartan-6, Virtex-5, Virtex-6 |
| M25PE | 1Mb – 16Mb | Spartan-3E, Spartan-3A, Spartan-3A DSP, Spartan-6, Virtex-5 | |
| M45PE | 1Mb – 16Mb | Spartan-3E, Spartan-3A, Spartan-3A DSP, Spartan-6 | |
| N25Q 3.3V (1) | 32Mb – 128Mb | Spartan-3E, Spartan-6, | |
| N25Q 1.8V (1) | 32Mb – 128Mb | Virtex-6 | |
| Atmel | AT45DB (RevB, C, and D) | 1Mb – 64Mb | Spartan-3E, Spartan-3A, Spartan-3A DSP, Spartan-6, Virtex-5, Virtex-6 |
| Winbond | W25Q (Rev V/CV) | 4Mb – 64Mb | Spartan-6 |
| W25Q (Rev BV) | 4Mb – 128Mb | Spartan-6 | |
| W25Q 1.8V (RevBW) | 4Mb | Virtex-6 | |
| W25Q 1.8V (RevBW) | 8Mb | Spartan-6 | |
| W25Q 1.8V (RevDW) | 64Mb | Virtex-6 | |
| Spansion | S25FLxxP (2) | 32Mb – 128Mb | Spartan-3A, Spartan-3A DSP, Spartan-6, Virtex-5, Virtex-6 |
- For Numonyx N25Q: Top, Bottom, and Uniform block sectors aresupported.
- S25FL032P, S25FL064P, and S25FL129P are supported. 64kB sectorsize only. S25FL128P is not supported.
iMPACT BPI Flash Programming Support
7 Series FPGA Family Support
| FlashVendor | Flash Family | Supported Flash Density | Data Bus Width | BPI Indirect Programming Support (1) |
| Micron (Numonyx) | P33 (Axcell™) | 64Mb – 1Gb | D[15:0] (x16) | Kintex-7 |
| P30 (Strataflash™, Axcell™) | 64Mb – 1Gb | D[15:0] (x16) | Kintex-7, Virtex-7, Artix-7 | |
| M29EW | 64Mb – 1Gb | D[15:0] (x16) | Kintex-7, Virtex-7 , Artix-7 | |
| D[7:0] (x8) | ||||
| G18F (2) | 128Mb – 1Gb | D[15:0] (x16) | Kintex-7, Virtex-7, Artix-7 | |
| Spansion | S29GLxxP | 128Mb – 1Gb | D[15:0] (x16) | Kintex-7, Virtex-7 |
| D[7:0] (x8) | ||||
| S29GLxxS | 128Mb – 1Gb | D[15:0] (x16) | Kintex-7, Virtex-7, Artix-7 | |
- Indirect BPI programming supports using the 7 series (Virtex-7 and Kintex-7)RS[1:0] pins when they are tied to the upper two BPI Flash addresspins..
- For Micron G18: Non-Mux interface family members are supported.
Virtex and Spartan FPGA Family Support
| FlashVendor | Flash Family | Supported Flash Density | Data Bus Width | BPI Indirect Programming Support (1) (2) |
| Xilinx® | XCF128X | 128Mb | D[15:0] (x16) | Virtex-5, Virtex-6 |
| Micron(Numonyx) (3) | P30 (Strataflash™,Axcell™) | 64Mb – 1Gb | D[15:0] (x16) | Spartan-6, Virtex-5, Virtex-6 |
| P33 Axcell | 64Mb – 1Gb | D[15:0] (x16) | Spartan-6 | |
| J3 (Rev D, F) | 32Mb – 256Mb | D[15:0] (x16) | Spartan-6, Virtex-5 | |
| D[7:0] (x8) | Spartan-3A, Spartan-3A DSP, Spartan-6, Virtex-5 | |||
| Spansion | S29GLxxS | 128Mb – 1Gb | D[15:0] (x16) | Spartan-6, Virtex-6 |
| S29GLxxP | 128Mb – 1Gb | D[15:0] (x16) | Spartan-6, Virtex-5, Virtex-6 | |
| D[7:0] (x8) |
- Maximum indirect BPI Flash programming TCK frequency is 3 MHz.
- Indirect BPI programming supports using the Virtex-6 and Virtex-5 FPGARS[1:0] pins when they are tied to the upper two BPI Flash addresspins.
- For Micron (Numonyx) monolithic P30: Top and Bottom parameterboot type are supported, and symmetrical boot type are not supported. P30 48F4400P0 Flash are also supported.
Zynq-7000 Flash Programming Support
Zynq™-7000 Quad SPI Flash Programming Support
| FlashVendor | Flash Family | Supported Flash Density | Mode |
| Micron | N25Q128A | 128Mb | single, dual_parallel |
| Spansion | S25FL128S | 128Mb | single, dual_parallel |
Zynq-7000 NOR Flash Programming Support
| FlashVendor | Flash Family | Supported Flash Density | Bus Data Width |
| Micron | M29EW | 32Mb - 256Mb | D[7:0] (x8) |
Zynq-7000 NAND Flash Programming Support
| FlashVendor | Flash Family | Supported Flash Density | Bus Data Width |
| Micron | 29F | 1Gb - 8Gb | x8 / x16 |
© Copyright 1995–2013, Xilinx®Inc. All rights reserved.
最后
以上就是温暖书包为你收集整理的FPGA配置flash的全部内容，希望文章能够帮你解决FPGA配置flash所遇到的程序开发问题。
如果觉得靠谱客网站的内容还不错，欢迎将靠谱客网站推荐给程序员好友。
本图文内容来源于网友提供，作为学习参考使用，或来自网络收集整理，版权属于原作者所有。
发表评论 取消回复