概述
Verilog HDL 程序举例
一，基本组合逻辑功能：
双向管脚（clocked bidirectional pin）
Verilog HDL: Bidirectional Pin
This example implements a clockedbidirectional pin in Verilog HDL.
The value of OE determines whether bidir isan input, feeding in inp, or a tri-state, driving out the value b.
bidir.v
module bidirec (oe, clk, inp, outp, bidir);
// Port Declaration
input oe;
input clk;
input [7:0] inp;
output [7:0] outp;
inout [7:0] bidir;
reg [7:0] a;
reg [7:0] b;
assign bidir = oe ? a : 8'bZ ;
assign outp = b;
// Always Construct
always @ (posedge clk)
begin
b <= bidir;
a <= inp;
end
endmodule
多路选择器（MUX）
//
//-----------------------------------------------------------------------------------
// DESCRIPTION : Multiplexer
// Code style: used casestatement
// Width of output terminal: 8
// Number of terminals: 4
// Output enable active: HIGH
// Output value of all bits whenenable not active: 0
//-----------------------------------------------------------------------------------
module mux(EN ,IN0 ,IN1 ,IN2 ,IN3 ,SEL ,OUT);
input EN ;
input [7:0] IN0 ,IN1 ,IN2 ,IN3 ;
input [1:0] SEL ;
output [7:0] OUT ;
reg [7:0] OUT ;
always @(SEL or EN or IN0 or IN1 or IN2 or IN3 )
begin
if (EN == 0) OUT = {8{1'b0}};
else
case (SEL )
0 : OUT = IN0 ;
1 : OUT = IN1 ;
2 : OUT = IN2 ;
3 : OUT = IN3 ;
default :OUT = {8{1'b0}};
endcase
end
endmodule
二进制到BCD码转换
//
//
//-----------------------------------------------------------------------------------
// DESCRIPTION : Binto Bcd converter
// Input (data_in) width : 4
// Output (data_out) width : 8
// Enable (EN) active : high
//-----------------------------------------------------------------------------------
module bin2bcd (data_in ,EN ,data_out );
input [3:0] data_in ;
input EN ;
output [7:0] data_out ;
reg [7:0] data_out ;
always @(data_in or EN )
begin
data_out = {8{1'b0}};
if (EN == 1)
begin
case (data_in [3:1])
3'b000 :data_out [7:1] = 7'b0000000;
3'b001 :data_out [7:1] = 7'b0000001;
3'b010 :data_out [7:1] = 7'b0000010;
3'b011 :data_out [7:1] = 7'b0000011;
3'b100 :data_out [7:1] = 7'b0000100;
3'b101 :data_out [7:1] = 7'b0001000;
3'b110 : data_out[7:1] = 7'b0001001;
3'b111 :data_out [7:1] = 7'b0001010;
default :data_out [7:1] = {7{1'b0}};
endcase
data_out [0] = data_in[0];
end
end
endmodule
二进制到格雷码转换
//-----------------------------------------------------------------------------------
// DESCRIPTION : Binto gray converter
// Input (DATA_IN) width : 4
// Enable (EN) active : high
//-----------------------------------------------------------------------------------
module BIN2GARY (EN ,DATA_IN ,DATA_OUT );
input EN ;
input [3:0] DATA_IN ;
output [3:0] DATA_OUT ;
assign DATA_OUT [0] = (DATA_IN [0] ^ DATA_IN [1] ) && EN ;
assign DATA_OUT [1] = (DATA_IN [1] ^ DATA_IN [2] ) && EN ;
assign DATA_OUT [2] = (DATA_IN [2] ^ DATA_IN [3] ) && EN ;
assign DATA_OUT [3] = DATA_IN [3] && EN ;
endmodule
7段译码器
//-----------------------------------------------------------------------------------
// DESCRIPTION : BIN to seven segments converter
// segment encoding
// a
// +---+
// f | |b
// +---+ <- g
// e | | c
// +---+
// d
// Enable (EN) active : high
// Outputs (data_out)active : low
//-----------------------------------------------------------------------------------
module bin27seg (data_in ,EN ,data_out );
input [3:0] data_in ;
input EN ;
output [6:0] data_out ;
reg [6:0] data_out ;
always @(data_in or EN )
begin
data_out = 7'b1111111;
if (EN == 1)
case (data_in )
4'b0000:data_out = 7'b1000000; // 0
4'b0001:data_out = 7'b1111001; // 1
4'b0010:data_out = 7'b0100100; // 2
4'b0011:data_out = 7'b0110000; // 3
4'b0100:data_out = 7'b0011001; // 4
4'b0101:data_out = 7'b0010010; // 5
4'b0110:data_out = 7'b0000011; // 6
4'b0111:data_out = 7'b1111000; // 7
4'b1000:data_out = 7'b0000000; // 8
4'b1001:data_out = 7'b0011000; // 9
4'b1010:data_out = 7'b0001000; // A
4'b1011:data_out = 7'b0000011; // b
4'b1100: data_out= 7'b0100111; // c
4'b1101:data_out = 7'b0100001; // d
4'b1110:data_out = 7'b0000110; // E
4'b1111:data_out = 7'b0001110; // F
default:data_out = 7'b1111111;
endcase
end
endmodule
二，基本时序逻辑功能：
8位数据锁存器
//
//
//-----------------------------------------------------------------------------------
// DESCRIPTION : Flip-flopD type
// Width : 8
// CLK active : high
// CLR active : high
// CLR type : synchronous
// SET active : high
// SET type : synchronous
// LOAD active : high
// CE active : high
//-----------------------------------------------------------------------------------
module ffd (CLR , SET , CE , LOAD , DATA_IN, DATA_OUT , CLK );
input CLR , SET , CE , LOAD , CLK ;
input [7:0] DATA_IN ;
output [7:0] DATA_OUT ;
reg [7:0] DATA_OUT_TEMP;
always @(posedge CLK )
begin
if (CE == 1'b1)
if (CLR == 1'b1)
DATA_OUT_TEMP ={8{1'b0}};
else if (SET == 1'b1)
DATA_OUT_TEMP ={8{1'b1}};
else if (LOAD == 1'b1)
DATA_OUT_TEMP =DATA_IN ;
end
assign DATA_OUT = DATA_OUT_TEMP;
endmodule
移位寄存器
//-----------------------------------------------------------------------------------
// DESCRIPTION : Shift register
// Type : univ
// Width : 4
// Shift direction: right/left(right active high)
//
// CLK active : high
// CLR active : high
// CLR type : synchronous
// SET active : high
// SET type : synchronous
// LOAD active : high
// CE active : high
// SERIAL input : SI
//-----------------------------------------------------------------------------------
module shft_reg (CLR , SET , DIR , CE ,LOAD , DATA , SI , data_out , CLK );
input CLR , SET , CE , LOAD , DIR , SI ,CLK ;
input [3:0] DATA ;
output [3:0] data_out ;
reg [3:0] TEMP;
always @(posedge CLK )
begin
if (CE == 1'b1)
if (CLR == 1'b1)
TEMP ={4{1'b0}};
else if (SET == 1'b1)
TEMP ={4{1'b1}};
else if (LOAD == 1'b1)
TEMP = DATA ;
else if (DIR == 1'b1)
TEMP = {SI ,TEMP [3:1]};
else
TEMP = {TEMP[2:0], SI };
end
assign data_out = TEMP;
endmodule
三，基本语法，元件例化与层次设计：
Verilog HDL: Creating a Hierarchical Design
This example describes how to create ahierarchical design using Verilog HDL.
The file top_ver.v is the top level, whichcalls the two lower level files bottom1.v and bottom2.v.
vprim.v
top_ver.v
module top_ver (q, p, r, out);
input q, p, r;
output out;
reg out, intsig;
bottom1 u1(.a(q), .b(p), .c(intsig));
bottom2 u2(.l(intsig), .m(r), .n(out));
endmodule
--------------------------------------------------------------------------------
bottom1.v
module bottom1(a, b, c);
input a, b;
output c;
reg c;
always
begin
c<=a & b;
end
endmodule
--------------------------------------------------------------------------------
bottom2.v
module bottom2(l, m, n);
input l, m;
output n;
reg n;
always
begin
n<=l | m;
end
endmodule
四，状态机举例：
同步状态机
Verilog HDL: Synchronous State Machine
statem.v
module statem(clk, in, reset, out);
input clk, in, reset;
output [3:0] out;
reg [3:0] out;
reg [1:0] state;
parameter zero=0, one=1, two=2, three=3;
always @(state)
begin
case (state)
zero:
out = 4'b0000;
one:
out = 4'b0001;
two:
out = 4'b0010;
three:
out = 4'b0100;
default:
out = 4'b0000;
endcase
end
always @(posedge clk or posedge reset)
begin
if (reset)
state = zero;
else
case (state)
zero:
state = one;
one:
if (in)
state = zero;
else
state = two;
two:
state = three;
three:
state = zero;
endcase
end
endmodule
最后
以上就是甜蜜钢笔为你收集整理的大量的verilog源代码的全部内容，希望文章能够帮你解决大量的verilog源代码所遇到的程序开发问题。
如果觉得靠谱客网站的内容还不错，欢迎将靠谱客网站推荐给程序员好友。
发表评论 取消回复